SEALXTREME PLUS Active Leak Repair Kit (SALRK)

SEALXTREME® PLUS Active Leak Repair Kit seals active pressurised leak under 30 minutes. It stops leaks on pipe without the requirement of system shut down. The maximum pressure Active Leak Repair Kit can seal is approximately 1.03 MPa (150 psi / 10 Bar) of live operating water pressure. This is a specially formulated wrap repair system that is durable and cost effective to seal pipe leaks with high industrial strength.

Features:

  • Perform active leak repair for pressure up to 1.03 MPa (150 psi / 10 bar)
  • No system shutdown required
  • Fix active leaks in less than 30 minutes
  • Hand applied
  • Works on both metal and non-metal pipes
  • Enhance chemical resistance
  • Repair and extend pipe life
  • Environmentally friendly, reduce carbon footprint
SEALXTREME PLUS ACTIVE LEAK REPAIR KIT

PACKAGING INFORMATION

PRODUCT CODEPRODUCTIMPA CODE
SNLRK02062 inch x 6 feet812367
SNLRK03093 inch x 9 feet812367
SNLRK04124 inch x 12 feet812367

GUIDELINES FOR BEST PRACTICE

PIPE DIAMETERPIPE PRESSURE
0.35 MPa (50 psi)
PIPE PRESSURE
1.03 MPa (150 psi)
SIZEKIT SIZEQTYKIT SIZEQTY
15 mm½ inch2 inch x 6 feet12 inch x 6 feet1
20 mm¾ inch2 inch x 6 feet12 inch x 6 feet1
25 mm1 inch2 inch x 6 feet12 inch x 6 feet1
32 mm1¼ inch2 inch x 6 feet12 inch x 6 feet2
40 mm1½ inch2 inch x 6 feet22 inch x 6 feet2
50 mm2 inch3 inch x 9 feet13 inch x 9 feet1
65 mm2½ inch3 inch x 9 feet13 inch x 9 feet1
80 mm3 inch3 inch x 9 feet14 inch x 12 feet2
100 mm4 inch3 inch x 9 feet14 inch x 12 feet2
125 mm5 inch4 inch x 12 feet24 inch x 12 feet2
150 mm6 inch4 inch x 12 feet24 inch x 12 feet2
200 mm8 inch4 inch x 12 feet24 inch x 12 feet3
250 mm10 inch4 inch x 12 feet34 inch x 12 feet4
300 mm12 inch4 inch x 12 feet44 inch x 12 feet5
350 mm14 inch4 inch x 12 feet44 inch x 12 feet6
400 mm16 inch4 inch x 12 feet54 inch x 12 feet7
450 mm18 inch4 inch x 12 feet54 inch x 12 feet8
>450 mm>18 inchContact Us

TECHNICAL DATA

PARAMETERVALUE
Tensile Strength36,000 psi
Lap Shear Strength900 psi
Flexural Strength26,000 psi
Application Temperature0 °C to 65 °C
Dielectric Strength16,000 Volts
Hardness85 Shore D
Service temperature-50 °C to 120 °C
Design Pressure400 psi

HOW TO APPLY

  • Safety first, wear appropriate protective gear. Gloves are a must
  • Knead the epoxy stick until 80% harden
  • Place the 80% cure epoxy stick beside the leak
  • Wrap the sealing tape on the epoxy stick
  • Gravitate the sealing tape and push the epoxy stick towards the leak
  • Continue wrapping the pipe with sealing tape until the leak stops
  • Dip the fiberglass repair tape in water for 5 seconds
  • Reinforce the repair area with fiberglass repair tape
  • Polish the surface of fiberglass repair tape with water and rub in a parallel direction with the pipe
+ +